Increase climbing figs - How it works by cuttings and sinkers


The Content Of The Article:

The climbing fig is one of the most popular indoor plants among hobby gardeners. It is easy-care, undemanding and can also be easily reproduced.

To increase climbing fig

Growing up and easy to care for, the climbing fig makes up many friends quickly. So what could be more obvious than to look for ways to increase climbing figs and thus provide for offspring on the flower window or just give away a piece of gardening happiness on.

Below are some hints for a successful multiplication. You will not be faced with too great challenges and even laymen will have good results.

Climbing figs can be multiplied in two different ways:

  • cuttings
  • Absenker

The propagation through cuttings

The cuttings propagation is more common and faster.

When is the best time for the cuttings propagation?

Cuttings can be cut in spring. Two flies with one stone can literally be hit if the pruning is used to extract cuttings.

What is needed for the cuttings propagation?

For the propagation by cuttings a sharp knife is needed. In addition, planters are used, which are filled with seed soil. Furthermore, you need a plastic hood and a water glass.

  • sharp knife
  • planters
  • potting soil
  • plastic cover
  • water glass

How should a cuttings be?

In principle, all drive parts are suitable as cuttings, which are cut off in a length between five and ten centimeters.

" Tip: For cuttings that already have aerial roots, the rooting is very fast.

It should be strong and healthy shoots, the better the prospects for good breeding successes.

How to deal with the cutting?

The cuttings are cut first. The interface should be clean and accurate. It helps a sharp and germ-free cutting tool. After the interface is slightly dried, the cuttings can immediately into the ground. If the cuttings do not have aerial roots, it makes sense to place the cuttings first in a glass of water and wait for them in a warm and bright window seat until the roots have formed. This will not be long in the first place, because climbing figs are rooted comparatively quickly.

How should the planter be?

As planters are both plastic and clay pots. The cutting is usually left in the planter only until it has formed enough roots to be implemented in the actual plant pot. It makes sense to always cultivate several cuttings in a planter. This causes a compact and bushy growth from the beginning.

At what temperature do the cuttings root?

The cuttings rooted best at room temperature. Temperatures over 18 degrees are therefore a good prerequisite. The planter should be placed in a bright place, but it must be protected from direct sunlight.

How long does the rooting take?

Climbing figs form roots very quickly. It will only take a few weeks for the cuttings to become rooted. Particularly fast develop vigorous young plants from cuttings, which already had when planting on aerial roots. If the cuttings are planted in the soil immediately after cutting, it will take several weeks longer for enough roots to form.

" Tip: The rooting can be accelerated by a plastic hood is placed over the cutting and thus creates a mini-greenhouse.

Cuttings without aerial roots can be preferred in a water glass. The cutting is placed in a water glass after cutting and rooted in a bright and warm place. After eight to ten days, enough roots are present and the cuttings can be in the soil.

How are the cuttings to be watered?

The substrate should always be moist. It is particularly important to ensure that it does not come to waterlogging, this would not tolerate the young and sensitive roots. It is therefore better not to irrigate the substrate consistently, but to moisten only with the plant sprayer.

If the cutting is provided with a plastic hood, it should be aired daily so that no mold forms under the airtight seal of the planter.

The increase by lowering

Propagation is a method often used by experienced gardeners, mainly in outdoor crops. It takes a little more patience to develop a self-sufficient plant here.

What is a sinker?

Climbing figs are vine plants. As a rule, they stretch their branches upwards.To gain a sinker, a tendril is picked out and led into the ground. There it comes to the rooting of the Absenkers and it can attract an independent plant.

How should we proceed in detail?

In order to carry out this method, a larger planter is needed, or, you put a second plant pot immediately next to the climbing fig. Grab a vine and lead it into the ground. If there are already aerial roots on the shoot, nothing else needs to be done. If no roots are visible, the shoot can be easily scratched with a knife. The sinker is guided into the ground and covered well. The shoot tip looks out of the ground.

" Tip: Complain to the sinker so that it remains in the ground.

Now, patience is needed. After successful rooting, the Absenker can be separated from the mother plant and it has created a separate plant that can be cultivated in a separate planter on.

The advantages and disadvantages of both methods at a glance

methodadvantagesdisadvantage
cuttings✔ It is possible to win several cuttings quickly.
✔ Cuttings can be obtained from the end of the shoot.
✔ The rooting takes place quite fast.
✔ Several cuttings in a planter result in a bushy growth.
✖ Cuttings can only be cut by sufficiently developed plants.
Pflanz A planter, potting soil and a plastic hood are needed as cover.
✖ The care of the cuttings must not be neglected.
✖ Cuttings are sensitive and prone to waterlogging.
Absenker✔ The workload is quite low.
✔ The sinkers grow independently into independent plants.
✖ Only one plant is created from a sinker.
✖ A large planter is needed.
Bew The rooting is slower than cutting.

Video Board: Captains Courageous by Rudyard Kipling.

© 2019 EN.Garden-Landscape.com. All Rights Reserved. When Copying Materials - The Reverse Link Is Required | Site Map