Make creative candles yourself


The Content Of The Article:

Make creative candles yourself is a great craft idea for adults and - under instructions - also for children. When it smells of tangerines, cloves and cinnamon, the sweetish smell of homemade beeswax candles completes the pre-Christmas mood at home. DIY enthusiasts, who have enough time, can even make their own candle mold in a few simple steps. In addition to beeswax, you can of course also use old candle scraps. They receive a "second life". For lovers of detail, we present a great way to decorate candles with fine ornaments.

Make candles in pine cone shape yourself

Something very special is the casting of candles, if you make your own shape. As an image for individual candle shapes, natural materials such as nuts or pine cones do very well. With the help of a silicone rubber compound, a negative is poured, which later represents the actual casting mold. Use the candles themselves make beeswax primarily as a material. This not only smells good and has a great coloring, it has another important benefit: beeswax contains neither paraffin (petroleum) nor stearin (palm oil). Although palm oil is one of the renewable raw materials, for the cultivation of the rainforest is cleared. Before you start pouring the candles, you should lay out the workplace with a newspaper or a washable pad.
You need this:

  • empty, clean tin can
  • Cones, walnut or similar
  • Screw (compensation screw)
  • Bar or narrow wooden slat
  • Sticks or pens
  • line
  • wick
  • cork
  • rubber bands
  • Silicone rubber compound M4514
  • Hardener T51
  • needle
  • beeswax
  • Cutter knife

How to make the candle shape

Before casting the candles, the mold is made. First choose the shape for the future candle, for example by using a pin. Carefully pierce the pin on the flat side with a screw. Remove the screw and pass it through a thin metal rail. Or you pierce a wooden strip in such a way that afterwards the pin can still be screwed firmly on it.

Pour candle mold

Slowly pour the rubber compound around the pin so that all cavities are filled

Mix the silicone rubber compound with the hardener in the ratio indicated on the bottle and pour a 1 cm thick bottom into a clean tin can. Then hang the construction with the pin over the can, so that the pin is completely in the preserve. Then fill the cavity with rubber compound until it forms a smooth surface at the edge of the container. Use a needle to prick open the small bubbles. Place the jar in a safe place where the mass hardens for about 12 hours, preferably overnight.

Mold of rubber for self-cast candle

The finished mold with cones and a duplicate of wax

When the silicone rubber compound has solidified, you can carefully cut the mold out of the tin with tin snips. Then cut the mold on one side with the cutter. Tip: Cut a point at the top and bottom so that the parts can be put together better later on. Now you can carefully loosen the pin together with the holder made of rubber. Finished is the homemade mold, with which to pour creative candles! It usually lasts for many years.

Pour candle yourself

pour liquid wax into the candle mold

Remove the candle from the mold

Fix the mold with rubber bands and fill in liquid wax (left). When the wax has hardened, the finished candle can be removed from the mold (right)

Now it goes to the actual pouring of the candle. Melt the beeswax in a small pot in a water bath. Seal the rubber mold with rubber bands. Cut the wick to the appropriate length and clamp it between two sticks so that a small piece of wick sticks out over the pins. Crayons are also good for fixing the wick. Wrap both ends of the sticks tightly with string and place it over the mold so that the long portion of the wick protrudes into the mold. Carefully pour the hot beeswax into the mold. Now wait for the wax to harden. Finally, loosen the pins from the wick, remove the rubber bands from the mold and open the rubber mold. The result is a self-cast candle in the form of the pine cone! Of course, this method can also be implemented with many other forms.

Pour pillar candles from wax residues

The soft glow of the candle flame creates a warm and calm atmosphere at home. But who does not know that? First, the candle burns beautifully, but then it starts to flicker and goes out - although there is still a lot of wax.The solution for unused candle remains is: Upcycling! Collect old candles and wax residues and process them into new candles. Straight pillar candles can be easily cast by yourself. For example, cardboard rolls are very suitable as casting molds.

Stumpenkerze

Even cast pillar candles can be arranged for Christmas

You need this:

  • candle remains
  • wick
  • old pot
  • Cardboard roll (kitchen roll, toilet paper)
  • tin can
  • toothpick
  • sand
  • bowl

Manual:

First sort the wax residues for colors before you melt them. If you do not have enough leftovers of one color, you can either pour multicolored candles or mix them. For example, blue and red become violet. But beware: Mix too many different colored wax residues, you will end up with brown candles! Once you have decided on a color scheme, melt the remnants of wax in an old pot one at a time, or mix together. You can also use an old tin can put in a hot water bath - but it gets very hot!
Now prepare the mold. Insert the toothpicks across the top of the cardboard tube. Now attach the wick to the toothpick so that it hangs in the center of the roll. Place the cardboard roll in a sand-filled bowl before starting to light the candle. Press lightly so that the wax does not flow out of the mold. After filling it carefully, allow the wax to harden well. The cooler the room, the faster it gets hard. If it is firm but still slightly warm, remove the candle from the bowl and gently pull off the cardboard roll.

Engrave candles yourself

With handmade ornaments you can give your candles that special something. The soft wax can be very well engraved and customized.
You need this:

  • candles
  • paper
  • pencil
  • masking tape
  • Small Drilling Machine (e.g., Dremel 300 Series)
  • Engraving knife attachment (eg Dremel Engraving Knife 105)
  • soft brush

Record template for engraving

Engrave candle with a Dremel

With a pencil, the decor can be transferred to the candle (left). The fine structures are then reworked with a multifunctional tool (right)

Cut out a piece of paper that fits around the candle. Draw a pattern of wavy lines, leaves, stars or dots on the paper in pencil. Then wrap the paper around the candle and fix it with masking tape. Draw the pattern with a pencil or a thick needle to transfer it to the candle. Now engrave the pattern in the wax with the drill and the engraving knife. With the soft brush you can remove the excess wax from the candle.

Video Board: 18 CUTE CANDLES YOU CAN MAKE YOURSELF.

© 2019 EN.Garden-Landscape.com. All Rights Reserved. When Copying Materials - The Reverse Link Is Required | Site Map