Lay the curbs correctly and set


The Content Of The Article:

Lay the curbs correctly and set: correctly

By means of curbs you can enclose paths, paved areas or even flower beds and thus make a garden shapely with the help of a path or a discount. This guide will help you with the correct setting of curbs, so that you can do without an expensive specialist:

Materials and preparation of curb installation

Keep in mind that to lay curbs yourself, you have enough space for your work and for storing the materials. In case of emergency, clear some space or clarify with your neighbor if you can use the public area of ​​the walkway. In any case, make sure not to obstruct the traffic of the cars or pedestrians. Remember: good planning in advance will make your work easier and smoother later on. First, make a list for the materials you need. Only when you have determined quantity, you can get the materials and aids.
Required tools:
  • patch hammer
  • patch cord
  • plaster iron
  • shovel
  • rüttelplatte
  • Tray for stirring the concrete
Required materials:
  • Curb made of granite, concrete or natural stone
  • Antifreeze gravel
  • Paving concrete C25 / 30
For large and heavy marginal notes, ideally you will get a helper to facilitate the physically heavy work.

Preparation of the actual paving work

  1. Lay down foil or tarpaulins on lawns or pavements that you want to protect, so you can easily remove the excavated soil and pavement later.

  2. First, you should dig out a ditch, a so-called planie, at the point where the curbs are to be later. This should be about one third of the later curb height or 15 to 20 cm below the lower edge of the curb. This plan should be as straight as possible. The best way to compact this plan is with the vibrating plate.

  3. Now fill in approx. 15 cm antifreeze gravel to avoid later frost damage such as cracking. This layer is also compacted again with the vibrating plate.

  4. Now hit the paving iron in the line or the escape of the later curbs.

  5. Between the paving iron, the paving line is stretched. This should have the height which should later also have the upper edge of the curbs. This work is one of the most important, because a crooked pavement can later lead to crooked curbs. Check the course and the height twice.

Lay curbs expertly

  1. Now bring the paving concrete to the beginning of the planie and along the paving line. When doing so, fill in the concrete slightly higher so that the curb is well inserted in the concrete bedding.

  2. Now you can put the first curb in the heaped concrete. Align the curb well and tap it with the paving hammer so that it is firmly in the concrete bed.

  3. Form the concrete bedding in front of and behind the curb into a wedge that you press down with the shovel and smooth. Although this area is later under the ground and is invisible, but helps, for example, later paving to lighter work.

  4. Now continue in this way with the remaining stones. Do not forget to check the distances, the height and the location again and again. Matching with the paving line is a good help here. Now you can make corrections.

  5. If large gaps between the curbs or natural stone was used, the joints should be filled with mortar.

Cost of self-laying curbs

Paving concrete and gravel is already starting from a few euros to get the bag. Stones, on the other hand, can have a large price range. From one euro or less the piece of simple concrete curb up to 15 euros the piece of natural stone is all possible. Therefore, it is precisely when using expensive natural stone necessary to determine the exact consumption of material. Nevertheless, buy a few more stones if they have measured themselves or perhaps need to cut one.

Sources of error, maintenance and care

Be sure to compact the excavated trench, especially if you are laying on sandy soil. Otherwise, even years later, when the ground lowers, the curbs may tip over or break the joints. Many lay people do without the inserted gravel, which is a big mistake. Especially this gravel prevents, when it is well compacted with the vibrating plate, the tilting or lowering of the curbs.
If you pay attention to these things, you will enjoy many years, if not decades, of your self-made curbs.

Meadow without lawn edge


Care or maintenance does not really need this small structure. If weed grows between the curbs, you can simply rip it out or remove it with Weed Ex. Just a curb prevents weeds from spreading from one surface to another, for example from grass to a bed.Thus, a set curb is not only a decorative but also a very useful building in your garden or front yard.

Worth knowing about the laying of curbs in the near future

If you have some manual skills, you can lay your own stones, save the craftsman and money, and later look proudly at the work of your own hands. Expert and prudent you will enjoy many years or even decades on your curbs. Here again the most important work steps at a glance:
  • With the spirit level, a straight line is staked using wooden sticks. These wooden sticks are now a string that serves as a guideline for the straight line and also for the height. Therefore, it is important that the cord also has the same height in all places.

  • Along the guide line, a trench is now dug, which is about a spade wide and about 20 cm deep.Bis half of this trench is then filled with a semi-moist concrete and set the curbs along the string.

  • Bring the curbs to the correct height with a rubber mallet. With it you can easily hammer on the edge stones, without this being damaged.

  • If the height is fixed, the curbs are filled with concrete on both sides. That's how they hold their bombs for many years.

If the fence is very heavily used, such as garage driveways or areas bordering a slope, a more stable edge must be created. This is realized by special concreted cornerstones, which can be deep curbs or palisades.
As an alternative to setting in concrete, the stones can also be anchored in a gravel bed. For this, the trench bottom is filled with a finger-deep layer of gravel. The curbs are placed on it, adjusted in height and direction and finally well embedded in fine gravel. This must be carefully compacted, which in turn can be used the rubber hammer. Of course you should not bring the stones back from their fixed orientation.

Curbs in the garden design

Clear lines in the garden, that's what most garden owners want. But it is always important that the overall picture is correct. Paths, beds, lawns and seats must harmonize. The curb stones also contribute to the perfect picture. But you should also think about practical things. Driveways to the house, the garage and the like must have a high stability. Garden paths are not so compact. This is more about optics. For driveways and the like offer concrete edge stones, for natural stones make way better. They often have a natural pattern. This relaxes the garden paths. Curbs are a real design element in the garden. Usually it looks more natural, if not everything is so perfect, so a stone out a little higher, one is lower. Too much perfection is often cold.
Conclusion
Curbs also contribute to the overall impression of the garden. Although they certainly set no highlights, but they provide with harmony. There are many different curbs. When choosing you should take your time. A specialist consultation can also be useful. It is important that a natural impression arises. The matching stones and a good laying technique contribute a lot to make the garden feel natural and inviting.

Lay the curbs correctly and set

FAQ - 💬

❓ How do you lay a kerb?

👉 How to Lay Edging Kerbs

  1. STEP 1: Excavation. Dig a trench. ...
  2. STEP 2: Mixture. To secure your edging blocks use: ...
  3. STEP 3: Laying. Use a taut string line to map out the line of your edging. ...
  4. STEP 4: Curved Lines. Use a spirit level to measure back to the taut line to check the height of curved edges. ...
  5. STEP 5: Flat Top Path Edging.

❓ What does curbs mean in architecture?

👉 Curbs and GuttersA curb, by definition, is something that restrains; an enclosing border or edging; a raised edge or margin; a wall; or as a verb, to strengthen or confine something. As most people think of curbs, they are raised strips of concrete along the edges of streets or parking lots.

❓ What is the mix for laying concrete kerbs?

👉 Concrete kerbs are generally laid with unfilled, close joints with a minimum joint width of 2 mm: they must not be butt-jointed. Mortar joints are not necessary but can be used for aesthetic reasons. The mortar should be freshly mixed, consisting of 1:4 cement: sand (by volume).

❓ How do you put in a kerb?

👉 Kerb units should be placed onto the concrete bed and tapped down to line and level using string lines to ensure the correct positioning is achieved. See images 2 & 3. Kerbs and edgings can be laid close jointed with 2 - 4mm joints without the use of mortar or with wider 5 - 10mm joints pointed with mortar.

❓ What is a kerb set?

👉 What is a kerb set? Kerbs are a line of stone which forms a rectangular edge covering the whole grave. This is usually made from the same stone as the headstone but can be changed for a contrasting material if preferred.

❓ What tools are used for laying kerbs?

👉 Here is a list of some of the common tools that are typically used for kerb stone laying:

  • Shovel for mixing concrete.
  • Concrete mixer or bucket for mixing.
  • Measuring tape.
  • String lines.
  • Hammer.
  • Chisel.
  • Rubber mallet.
  • Spirit level.

Video Board: How to lay Kerbs - Aggregate Industries Durakerb.

© 2024 EN.Garden-Landscape.com. All Rights Reserved. When Copying Materials - The Reverse Link Is Required | Site Map