Create gravel path correctly


The Content Of The Article:

Create gravel path correctly: create

There are no limits to the creative possibilities, so that, depending on taste and need, a gravel path can run straight, may have a curved or variable width routing. In addition, gravel has a high drainage ability, thereby preventing the formation of rain puddles.

Prepare garden path substructure - for a stable gravel path

Gravel paths are a real eye-catcher and fit harmoniously into any garden landscape as a decorative element. But a gravel path is also exposed to the weather conditions and requires sufficient stability. Because pebbles can slip when driving or walking. However, in order for the gravel path to achieve good stability, it is recommended to use plastic honeycomb panels as a substrate, which ensure good fastening.
preparation
First, the course and the shape of the path is marked, which takes place in a curved shape with a marking spray and in a straight course with embroidery and spade. In order for the curb stones to be set, the path should be dug out about 10 cm wider on each side.
Calculation Tip:
  • for middle and lower classes is to be calculated with about 8.50 euros per m²
  • and 2 Euro each for 50 cm long lawn edging stones
  • Depending on the available budget per m², the surface gravel can amount to approx. 15 - 20 Euro
Required tools and material
  • Mason's cord or nylon cord
  • leveling rails
  • rüttelplatte
  • bucksaw
  • straightedge
  • Laying chippings or laying sand
  • gravel
  • curbs
  • floor honeycomb

Creating a gravel road - single steps

Once all the curves have been planned and the course of the gravel path has been determined, the steel embroideries are struck in each case at the corner points and the nylon or masonry string is stretched. It should be noted that the cord is tensioned with the help of a spirit level at the same height, in which later the upper edges of the travel limit will be. For the cord to receive tension, proceed as follows:
  • first tie a loop and then pull the noose around the embroidery
  • Now put on tension and then wind three times from bottom to top for the next embroidery
  • Lift the live string with your left hand
  • and with the right hand pull the razor end underneath
  • pull down the left side again, so that the nylon cord itself clamps
  1. First the soil is sharpened with a spade along the already stretched cord. Now the road surface with a depth of 15 cm to 20 cm is excavated. If the gravel road is intended for heavier loads, the subsoil should be sufficiently load-bearing and approx. 35 cm deep. If it is created for driving by car, a separate construction of about 60 cm is required, however, depends on the local soil conditions. The resulting excavation can be either distributed in the garden or picked up by a container service.

  2. So that the gravel path receives a lateral boundary, lawn edging stones are buried in the gravel bed and hammered. The lawn edge stones must be checked again and again to an exact vertical alignment. The height of the left boundary edge depends on the height of the right edge and is a curve with planned in accordance with Rundpalisaden.

  3. The excavated area is now filled up to half with frost protection gravel (grain size 0/32). Then use a compactor that has a heavy metal base plate in the form of a stamp to thoroughly wet the sand. On the gravel layer follows a middle layer of 7 cm to 10 cm of laying chippings or laying sand, which is just pulled and also compacted.

  4. Now the floor honeycomb will be laid. It should be noted that the honeycomb is followed by a gravel layer of 2 cm. If you would like to do without floor honeycombs, you should lay a layer of garden fleece between the middle and upper layers to prevent the weeds and grass from growing through the gravel path from below.

  5. If floor honeycombs made of plastic material are used, these can now be cut very easily with a foxtail saw. In order to use all the plastic material, the cut pieces should be laid individually.

  6. If the honeycomb mats are completely laid, the gravel filling can be distributed just below the edges of the turf. Due to the stability of the mats, they can now be entered but not yet driven on.

  7. So that the honeycombs are completely filled, the gravel is evenly distributed and worked with the back of a rake.

  8. Once the surface has been completed, the roadsides that surround the gravel path can be decorated with decorative plants, for example.

Care of a gravel road

Gravel path garden design

Gravel paths look attractive, can be flexibly used, can be wonderfully combined with other path coverings and lend each garden a fascinating visual effect. Due to the material, however, this pathway also requires a more complex care in contrast to plate paths, for example.Even if garden fleece or foil is used, weeds can form again and again, which must be removed on a regular basis so that the path retains its neat appearance.

Worth knowing about the creation of a gravel road soon

A gravel path in your own garden is a very natural and cheap alternative to paved and Plattenwegen. Creating a gravel path is relatively easy and can be done without large and heavy machinery. However, the creation of a gravel road requires some work. In terms of design, all shapes are possible, so a round, organic and variable in width routing is easily possible. An advantage of a gravel path is that even when it rains no puddles can form, since the water can flow downwards.
Plan route
  • Before the gravel can be poured, the shape and the course of the gravel path must first be marked.
  • Either this is done by a spade, by means of a marking spray or by pulling strings.
  • Following this, the road surface is excavated to a depth of approximately 15 centimeters.
If you have enough space in another place in the garden, the accumulating soil can be layered to a wall and offers a nice place for a later planting. If this possibility does not exist, there are container services, which leave the earth.
Apply base layer
  • For the gravel road to get its necessary stability, a base course is necessary.
  • As a rule, a layer thickness of 10 to 13 cm is sufficient.
  • Mineral mixtures or recycled ballast, which are available in the building materials trade, are used for this purpose.
  • This base course is filled up to the upper edge of the excavated trench and compacted with a hand rammer.
If it is a larger road surface, renting a vibrating plate can be quite useful and a pleasant relief. Building material distributors rent such devices already from 30 Euro per day.
Apply gravel
  • Before the gravel lining can be poured up, a layer of garden fleece should be applied.
  • Garden fleece prevents the weed growth of the gravel path and can be easily laid out and trimmed with a standard pair of scissors.
  • Once this is done, the garden gravel is poured up.
By compacting the base layer, a gravel layer of two to three centimeters must be expected. This is just the right height of a gravel path, as with a thicker layer of gravel the foot would sink when entering. For a gravel path you should calculate per square meter costs in the amount of 9 euros.
Conclusion
Gravel paths are suitable for landscaping. They are a reasonably priced alternative to other types of routes and let water seep away well. If plastic floor honeycombs are used for the creation of a gravel path, it will receive a firm and stable hold, so that sinking is not possible. In addition, various design elements such as patterns or circles can be incorporated and different gravel colors can be used. Even if gravel paths need a higher maintenance effort to keep their neat appearance, they are a real eye-catcher in any garden.

Video Board: How to Build a Flagstone Walkway - This Old House.

© 2019 EN.Garden-Landscape.com. All Rights Reserved. When Copying Materials - The Reverse Link Is Required | Site Map