Building instructions for a fireplace


The Content Of The Article: For many people today, there is nothing better than spending a cozy and relaxing evening in front of the fireplace. The flaming flames, the flickering light has been a sedative effect on people since time immemorial. So it is not surprising that more and more people are planning an open fireplace when building a new house. But even for the owners of older houses is the subsequent installation of a fireplace and the associated, romantic campfire mood no problem. Thanks to the many prefabricated kits available from each manufacturer, a stove or a chimney without a chimney can easily be built today.
However, before you start building, there are a few things to keep in mind. First, you should ask your responsible chimney sweep, if all legal and structural requirements for the installation of a fireplace are given. On the basis of a report, the chimney sweep can then give you the green light.
Now it's time to choose the right material for plinth, ledge and walling. For the base and cladding, the use of aerated concrete has proven itself. The easy-to-use solid construction material has excellent thermal properties, which are of course of particular importance in connection with the high heat generation at the fireplace. Due to the low weight of the aerated concrete is also an excessive burden of blankets excluded, so you
Do not have to worry about the statics here.
Of course you need fireproof materials for the fireplace itself, but you should also use non-flammable building materials for the cladding. Again, the autoclaved aerated concrete, which by the way belongs to building material class A1, is recommended. In addition, it has a very poor conductivity of heat, so that the outside, so the side that faces away from the fire, has only low temperatures.
If you want to install an open fireplace, it must be clad on all sides. You can do this using planers or planing panels, which in turn should be made of aerated concrete. On the walls of the house, the cladding must be carried out as a bricklaying, planing slabs with thin-bed mortar can be walled. Because they are made with very small dimensional tolerances, so that this is easily possible. If you use aerated concrete blocks that are equipped with tongue and groove, they must only be grouted in the area of ​​the bearing joint. In the butt joint area you only need to push them together. This is also possible with the plan building boards, which are manufactured according to the same principle, but have a smaller wall thickness. The weight of the fireplace is supported by the base supports,
which should be the best of aerated concrete.
If you are installing an open fireplace, you must also ensure that the surfaces of the cladding and those of niches for the storage of the fuels to max. Heat 85° C. If you use aerated concrete, it will increase to 120° C. However, this does NOT affect the places where you want to place things, such as the mantel clock or the family photos on the ledge. However, this regulation applies only to the surfaces mentioned above, but not to doors or other components which close the combustion chamber.
If a new chimney has to be created in preparation of your new chimney construction, molded concrete blocks are also available, with which you can cover the additionally insulated pipes in the interior. Most of these are available as plug-in systems, so that they take little time during assembly. The aerated concrete blocks can also be grouted with thin-bed mortar without any problem.
Now that you have decided on the ideal location of the fireplace and bought all the necessary components and materials, you can start. However, you should start the construction
Carefully read the assembly instructions provided with the prefabricated kits. At the beginning, the insole is laid out on the floor and the outside outline is recorded. Move a little bit inwards, and then draw another line, where you start to open the pedestal. So you have created a small overhang that protects your ground against flying sparks. Now the interior of the fireplace is used. It is best to build it exactly according to the manufacturer's instructions. After the construction has been completed successfully, you can start with the bricking, the walling and the cladding of the fireplace. Often, the open fireplaces are built on the corner, so that here the cellular concrete recommends again. Because this can be easily sawed and in over-corner buildings known to have many bevels are performed. Even round or half round parts can be easily made.
When you have finished the walling and cladding, you should only render the aerated concrete surface with a plaster. You can put this on as a whole fabric as a tissue, so that the plastering should go quite easily by the hand.
However, you can only view this construction manual as a rough guideline, because the specifications of the individual manufacturers are sometimes so different that no uniform instructions can be given. It is best that you follow the exact procedure, as described in the construction manual of your fireplace kit. So you are sure to get a functional and shapely heat donor.
When everything is finished, you should not hesitate and dedicate your fireplace. Best with a glass of wine and a bearskin in front of it. Thus, the work is rewarded with a well-deserved cozy evening for two.

Building instructions for a fireplace

FAQ - 💬

❓ How do you build a fireplace?

👉 How to Build a Gas Fireplace

  1. Determine Where You'll Install the Fireplace. ...
  2. Build a Platform for the Insert. ...
  3. Install the Vent Pipe. ...
  4. Hire a Plumber and Electrician. ...
  5. Build a Frame Around the Insert. ...
  6. Build the Mantel. ...
  7. Build the Hearth. ...
  8. Apply the Finish.

❓ How to build an outdoor fireplace step by step?

👉 How To Build an Outdoor Fireplace

  1. Locate the Outdoor Fireplace. ...
  2. Clear and Level the Area for the Pad. ...
  3. Build the Fireplace Pad Form. ...
  4. Pour the Fireplace Pad Concrete. ...
  5. Allow the Concrete to Cure. ...
  6. Lay the Fireplace's Wood Box. ...
  7. Create the Lintel. ...
  8. Lay the Hearth Blocks.

❓ How to build a fireplace with fire brick?

👉 On. Between bricks he switches to fire resistant mortar because the joints will be exposed to combustion. It has a fire rating up to 2500. Degrees.

❓ How do you start a fireplace?

👉 And you're kidding you'll light the kindling. And it'll burn down to the larger locks. The log cabin stack is probably the most common stack it's where you take the logs.

❓ Can I build a fireplace myself?

👉 It's possible to do a DIY installation of an electric fireplace. However, it's better to hire a professional to install a wood-burning fireplace with a chimney or a direct-vent gas fireplace. Building a chimney or installing a gas line can be complicated projects.

❓ How were old fireplaces built?

👉 Early fireplaces were made of stone; later, brick became more widely used. A medieval discovery revived in modern times is that a thick masonry wall opposite the fireplace is capable of absorbing and re-radiating heat. From early times fireplace accessories and furnishings have been objects of decoration.

❓ How do you build a fireplace?

👉 A main component of Fireplace is its firebox. The fireplace opening is placed with steel frame glass door. Build the firebox itself with nine-inch refractory mortar and firebrick laid on edge. Use the glass door frame as a template for the sizing.

❓ How do you put a fireplace insert in a wall?

👉 With a prybar, remove the baseboard from the wall. You'll use two-by-sixes a build a frame to hold the fireplace insert within the fireplace wall. The frame's inside dimensions should match the size of the fireplace insert's rough opening dimensions, with 1/8-inch extra on all sides.

❓ How do you build a top-down fire in a fireplace?

👉 To build a top-down fire in your fireplace you’ll want to take your largest sized logs and place them together in a row at the base of your fireplace or grate. The logs should be packed together horizontally so that they’re touching to allow the fire to be more easily transferred across the row of logs.

❓ How do you build a fireplace with a KREG jig?

👉 Start by building the two supporting sides of your fireplace using two-strip boards cut to your desired measurements. Go ahead and build the front frames using the remaining 2 strip boards and Kreg Jig. Use a stud finder and wood screws to attach the common boards. When attaching, ensure that the boards are straight and properly levelled.

Video Board: Build a Fire, How to Make a Fire Quick and Easy Pro Instruction.

© 2024 EN.Garden-Landscape.com. All Rights Reserved. When Copying Materials - The Reverse Link Is Required | Site Map